|Unit of||electric conductance|
|Named after||Ernst Werner von Siemens|
|1 S in ...||... is equal to ...|
|SI base units||kg−1⋅m−2⋅s3⋅A2|
|inverse ohm||1 Ω−1|
The siemens (symbol: S) is the unit of electric conductance, electric susceptance, and electric admittance in the International System of Units (SI). Conductance, susceptance, and admittance are the reciprocals of resistance, reactance, and impedance respectively; hence one siemens is redundantly equal to the reciprocal of one ohm (Ω−1) and is also referred to as the mho. The 14th General Conference on Weights and Measures approved the addition of the siemens as a derived unit in 1971.
The unit is named after Ernst Werner von Siemens. In English, the same word siemens is used both for the singular and plural. Like other SI units named after people, the symbol is capitalized but the name of the unit is not. For the siemens this is particularly important to distinguish it from the second, symbol (lower case) s.
The related property, electrical conductivity, is measured in units of siemens per metre (S/m).
For an element conducting direct current, electrical resistance R and electrical conductance G are defined as
The unit siemens for the conductance G is defined by
For a device with a conductance of one siemens, the electric current through the device will increase by one ampere for every increase of one volt of electric potential difference across the device.
The conductance of a resistor with a resistance of five ohms, for example, is (5 Ω)−1, which is equal to 200 mS.
A historical equivalent for the siemens is the mho (//). The name is derived from the word ohm spelled backwards as the reciprocal of one ohm, at the suggestion of Sir William Thomson (Lord Kelvin) in 1883. Its symbol is an inverted capital Greek letter omega: U+2127 ℧ INVERTED OHM SIGN.
The SI term siemens is used universally in science and often in electrical applications, while mho is still used in some electronic contexts.
The inverted capital omega symbol (℧), while not an official SI abbreviation, is less likely to be confused with a variable than the letter 'S' when writing the symbol by hand. The usual typographical distinctions (such as italic for variables and roman for units) are difficult to maintain. Likewise, it is difficult to distinguish the symbol 'S' (siemens) from the lower-case 's' (seconds), potentially causing confusion. So, for example, a pentode’s transconductance of 2.2 mS might alternatively be written as 2.2 m℧ or 2200 μ℧ (most common in the 1930s) or 2.2 mA/V.
A handwritten 'S' can also be misread as the frequency-space variable 's', commonly used in transfer functions.
Notes and references
- Minutes (PDF). 14th General Conference on Weights and Measures. 1971. p. 78.
- "Chapter 9: Rules and Style Conventions for Spelling Unit Names". NIST Guide to the SI (Report). National Institute of Standards and Technology. 2008. Archived from the original on 2019-05-06. Retrieved 2017-12-22.
- Thomson, William (1884). "Electrical Units of Measurement". The Practical Applications of Electricity. Institution of Civil Engineers. pp. 149–174 at p 171 (Lecture given 3 May 1883). Available online. Thomson helpfully added that the proper pronunciation of "mho" could be obtained by taking a phonograph and turn it backwards.
- "Chapter 5: Units Outside the SI". NIST Guide to the SI (Report). National Institute of Standards and Technology. 2008. Retrieved 2017-12-22.
- Weiner, Eugene R. (2013). Applications of Environmental Aquatic Chemistry: A practical guide. CRC Press. p. 109. ISBN 978-1439853320.
- "Siemens (unit of electrical conductance)". www.tech-faq.com. 6 April 2019.